===== Aile volante V3 SEPT (2017) ===== Documents et sources en complément de l'atelier aile volante de septembre 2017\\ ===== Matériel ===== ELECTRONIQUE : - Motor: Racerstar Racing Edition 1806 BR1806 2280KV 1-3S [[https://goo.gl/xPbUFu|Banggood]]\\ - ESC: Racerstar RS20A Lites 20A Blheli 2-4S [[https://goo.gl/z4S5V7|Banggood]]\\ - Servos : MG90S Metal Gear RC Micro Servo [[https://goo.gl/Z2oHPh|Banggood]]\\ - Batterie : Turnigy Nano-Tech 1000mah 2S 25~50C Lipo Pack [[https://goo.gl/dbSVhR|Hobbyking]]\\ - Connectors: XT60 [[https://fpvracing.ch/en/components/119-xt60-male-female-bullet-connectors-plugs-for-rc-battery.html|FPVRacing.ch]] or XT30 [[https://goo.gl/wYKCZg|Banggood]]\\ - Propellers: 5×4.5×3 5045 [[https://goo.gl/evZtil|Banggood]]\\ - BEC Diatone 5V 2A: [[https://goo.gl/TWqGYi|Banggood]]\\ - LED Diatone DT-LED-901: [[https://goo.gl/SVJ23P|Banggood]]\\ - 26 AWG cables: [[https://fpvracing.ch/en/components/156-1m-silicone-wire-26awg-red-black.html|FPVRacing.ch]]\\ - Battery Voltage Tester: [[https://www.banggood.com/Wholesale-1S-8S-Li-po-Battery-Voltage-Tester-Checker-Indicator-Monitor-Buzzer-Alarm-p-26049.html?p=7G14111777398201506Z|Banggood]] FRAME : - Flying Blade 800mm Wingspan EPP Flying Wing\\ - Motor mount : 2mm plywood [[https://goo.gl/kuji0d|Coop]]\\ - Control horns & clevis: [[https://goo.gl/zf79uc|Banggood]]\\ - Metal Push Rods : [[https://goo.gl/JalWcr|AliExpress]]\\ - Laminate film: CP laminating film - 1.7 Mil [[http://alofthobbies.com/new-stuff-laminating-films.html|Aloft Hobbies]]\\ - Heat Shrink Tube [[https://goo.gl/kulUAh|FPVRacing.ch]]\\ - Hex socket screw M3x5 (for the motor mount)\\ - Claw nut M3 (for the motor mount) TOOLS - Razor blade\\ - Sandpaper : 120\\ - Tape with fiberglass, 25 mm [[https://www.swiss-composite.ch/|Swiss Composite]]\\ - Tape with fiberglass, 35 mm [[https://www.swiss-composite.ch/|Swiss Composite]]\\ - Tape with fiberglass, 50 mm [[https://www.swiss-composite.ch/|Swiss Composite]]\\ - Glue E6000 [[https://goo.gl/pPY9UV|Banggood]]\\ - CA (cyanoacrylate) : utiliser de la « thick », en mettre très peu (pour le poids et pour ne pas abimer la mousse). Accélérateur facultatif. - Hot glue gun [[https://goo.gl/d7Nkqh|Banggood]]\\ - Glue gun sticks: [[https://goo.gl/9TVMrZ|Banggood]]\\ - Fer a souder: [[https://goo.gl/57Yqth|Banggood]]\\ - Electric Heat Shrink Gun [[https://www.banggood.com/220V-300W-DIY-Electric-Heat-Shrink-Gun-Power-Tool-Hot-Air-Temperature-Gun-with-Supporting-Seat-Plastic-FIMO-p-1025199.html?p=7G14111777398201506Z|Banggood]]\\ - Servo tester [[https://goo.gl/BZoXaA|Banggood]] DIVERS : - Poche de protection pour batteries [[https://fpvracing.ch/en/transport-/962-lipo-safe-bag-230x290-mm.html|FPVRacing.ch]]\\ - Battery charger [[https://goo.gl/gxVki8|FPVRacing.ch]]\\ - Wrench for Lock Nut: [[https://fpvracing.ch/en/motors/898-wrench-for-lock-nut.html|FPVRacing.ch]]\\ - Lock Nut for motor CCW [[https://fpvracing.ch/en/motors/898-wrench-for-lock-nut.html|FPVRacing.ch]]\\ - Lock Nut for motor CW [[https://fpvracing.ch/en/motors/898-wrench-for-lock-nut.html|FPVRacing.ch]]\\ - Racerstar USB Linker Programmer [[https://goo.gl/nNAZt8|Banggood]] ===== Trucs et astuces ===== MONTAGE VOL - Toujours lancer et atterrir contre le vent\\ - N'oublier pas qu’en tournant votre aile à moins de portance, si votre vitesse est trop réduite elle va décrocher (passer du mode vole au mode je tombe comme une pierre)\\ - N'hésiter pas à la faire planer : couper le moteur, et voler: L’aile est moins stable à faible vitesse mais cela ne fera que renforcer votre expérience utilisateur. RADIO FrSky ACCST TARANIS X9D PLUS [[https://goo.gl/pSCcLI|FPVRacing]]\\ Flysky FS-i6X 2.4GHz [[https://goo.gl/ePDruo|Banggood]] VIDEO Connecter la radio avec le receiver: [[https://youtu.be/e4u_dEKP5Rs|https://youtu.be/e4u_dEKP5Rs]]\\ Synchronisation (Binding) Taranis 9XD Plus avec receiver D4RII: [[https://youtu.be/cD_xLRIt5N0|https://youtu.be/cD_xLRIt5N0]] ===== Liens Youtube ===== [[https://www.youtube.com/channel/UCsKONpvCpJdgVJXh-hqVscg|FabLab La cote]]\\ [[https://www.youtube.com/user/Painless360|Painless360]]\\ [[https://goo.gl/2YoQn7|bardwell]]\\ [[https://www.youtube.com/user/andyandvirg|Andrew Newton]]\\ [[https://www.youtube.com/user/RCModelReviews|RCModelReviews]]